ADVANTEC NEW TECHNOLOGY
High-performance brake module with cross-drilled ceramic disc and fixed caliper with laser-etched ADVANTEC engraving

ENGINEERING SERVICES · SINCE 1996

Engineers for the brakes of tomorrow.

ADVANTEC provides car manufacturers and suppliers with experienced engineers from a large network – worldwide, directly inside their development projects. Brakes first, but not only.

We support you worldwide in testing, validation, research and development.

BRAKE MODULE · STUDIO SHOTGUMMERSBACH · 51°02′N 7°34′E

1996

Founded in Gummersbach, Germany – now in its second generation

Patent

Ahead of our time since 1996 – with our own patent for temperature monitoring

On site

Deployed worldwide with manufacturers and suppliers

80+

Engineers, freelance engineers and technical consultants – on the road for you

Motorway at night with light trails

OUR MODEL · ENGINEERING SERVICES

We don’t manufacture. We bring know-how to where development happens.

ADVANTEC provides car manufacturers and suppliers with experienced engineers. Our engineers work directly inside our clients’ development teams – at their sites in Germany and worldwide.

Deployed worldwidePermanent & freelance engineersBrake specialists

01

Requirement

You describe the project, timeframe and the profile you need.

02

Selection

We assemble the right engineers from our team – permanent or freelance.

03

On-site

Our engineers join your teams and contribute their know-how directly.

ENGINEERING NETWORK

A network that grows with your projects.

Behind ADVANTEC stands a large network of permanent and freelance engineers: experienced specialists in brakes, chassis, test benches and vehicle testing. This lets us staff every requirement – from a single expert to a complete project team, worldwide.

80+

ON THE ROAD FOR YOU

More than 80 engineers, freelance engineers and technical consultants.

On the road for you – with manufacturers and suppliers in Germany and worldwide.

ADVANTEC

From expert to team

Individual specialists or entire project teams – matched to scope and phase.

Broad experience

Know-how from many vehicle projects with manufacturers and suppliers.

Worldwide

Our engineers work wherever development happens.

Drifting car in thick tyre smoke on a race track
01 / 03ADVANTEC · VALIDATION

VALIDATION · RACE TRACK

Where brakes meet their limits.

Lateral acceleration, hard load changes, temperature peaks: on the race track we validate components under conditions everyday driving never reaches.

At the limitLoad changesTelemetry

SERVICES

Expertise across the entire development chain.

Our engineers bring their know-how directly into your projects. Brakes are the core focus – with the same rigour we support further vehicle and component technologies.

01

Brake systems & materials

Development of lightweight, high-performance brake discs and friction pairings – including proprietary aluminium silicon carbide composites.

02

Thermal monitoring & sensors

Monitoring the thermal state of moving components – based on our patented technology that warns early when brake temperatures turn critical.

03

Test bench & validation

Test bench work for the automotive industry: reproducible measurements, reliable data and clear reports to base your decisions on.

04

Vehicle testing

Component testing under real driving conditions – on public roads and on the race track, where parts are pushed to their limits.

05

Development & consulting

Concept, design and technical consulting for road and racing vehicles – as an extension of your team or as a self-contained work package.

06

Patented know-how

With our 1996 patent we were ahead of our time. We bring that pioneering spirit into every project to this day.

TECHNOLOGY IN FOCUS

The aluminium silicon carbide brake.

Our brake disc combines an aluminium matrix with embedded silicon carbide particles. The result: significantly lower weight with high friction performance and fade resistance.

Less unsprung and rotating mass improves vehicle dynamics and efficiency – an advantage that matters especially for electric vehicles. With the brake particle limits of the Euro 7 standard, the material gains further relevance.

Arrange a technology briefing
DATA SHEETAL-SIC BRAKE DISC
Material
Aluminium matrix with silicon carbide particles
Weight
up to 60 % lighter than conventional systems
Emissions
significantly reduced brake wear particles
Applications
Passenger cars, electric vehicles, motorsport
Cost
significantly lower than carbon-ceramic
Developed by
ADVANTEC, Gummersbach

1996

Ahead of our time, even back then.

As early as 1996, ADVANTEC invented and patented a method for monitoring the thermal state of moving bodies: it was designed to warn the driver as soon as the brake system reaches a critical temperature. An idea that put us at the cutting edge back then – and a step ahead of our time.

The principle is as simple as it is effective: above a certain temperature – the so-called Curie temperature – a magnet loses its magnetism. The system detects exactly this moment and reports overheating before the brake is damaged.

That ambition still drives us today: what began with a patent in 1996 continues in every project – with engineers who break new ground and think technology ahead before it becomes the standard.

NSBELOW CURIE TEMPERATURET < T꜀ · magnet active!ABOVE CURIE TEMPERATURET ≥ T꜀ · magnetism lost → warning
Glowing brake disc on the test bench

TEST BENCH · HEAT TEST

Red heat is just another data point.

On the test bench we drive brakes deliberately into the critical temperature range. Our patented thermal monitoring warns as soon as things turn critical.

Thermal monitoringFade analysisEndurance load

BRAKE DISC IN THE CRITICAL TEMPERATURE RANGE

OUTLOOK · EURO 7

Euro 7 makes brake dust measurable. We make it smaller.

On 29 November 2026, Euro 7 introduces the first European limit for brake particle emissions. What used to be accepted as unavoidable becomes a type-approval requirement – and a development task for the entire industry.

Carbon-ceramic brakes are light and low-wear, but their price limits them to a few premium vehicles. Our aluminium silicon carbide brake costs significantly less. That makes it possible to equip a large part of the vehicle range with lower-dust brakes – not just the top end. This is how we contribute to cleaner mobility.

TIMELINE

  1. 29.11.2026Euro 7 applies to new type approvals (cars, light commercial vehicles)
  2. 29.11.2027Limits apply to all new registrations
  3. 01.01.2035a uniform 3 mg/km for all powertrains

PM10 LIMITS FOR BRAKE WEAR

Combustion & hybrid7 mg/km
Battery-electric3 mg/km
All powertrains from 20353 mg/km

Source: Regulation (EU) 2024/1257 (Euro 7). Measured on a test bench.

OUR ASSESSMENT OF DISC MATERIALS

Grey cast ironCarbon-ceramicAl-SiC (ADVANTEC)
Weighthighvery lowlow
Brake wearhighlowlow
Costlowvery highwell below carbon-ceramic
Range of usevolume modelspremium, sports carsbroad vehicle range

Qualitative assessment by ADVANTEC; project-specific values on request.

SYSTEM ARCHITECTURE

Every component engineered. Down to the detail.

Our engineers treat the wheel brake as a complete system: material, friction pairing, thermal behaviour and sensors are designed together – not one after another.

BILL OF MATERIALS

ItemPartMaterialNote
01Wheel hubSteelBrake disc mounting
02Brake discAl-SiC compositelightweight
03Inner brake padFriction materialmatched to Al-SiC
04CaliperAluminiummulti-piston design
05Pistons–hydraulic actuation
06Outer brake padFriction materialmatched to Al-SiC
07Caliper bracket–knuckle mounting
08Temperature sensor–patented thermal monitoring
09Mounting boltsSteelassembly

Schematic illustration. Design is project-specific.

Orange rally prototype racing through a dust cloud

VALIDATION · DESERT

Heat. Dust. Endurance.

Long-distance testing in extreme environments – so that brakes and sensors work reliably in heat and fine dust.

HeatDust ingressEndurance

03 / 03 · DUST INGRESS AT FULL LOAD

APPROACH

Our engineers support every phase – inside your team.

  1. 01

    Analysis

    Clarify requirements, specifications and trade-offs.

  2. 02

    Concept

    Evaluate options, define materials and dimensioning.

  3. 03

    Prototype

    Design and build of first functional samples.

  4. 04

    Test bench

    Reproducible measurements under defined conditions.

  5. 05

    Testing

    Driving trials on road and race track.

  6. 06

    Series support

    Transfer to production, licensing and support.

INSIGHTS

Tested where it matters.

Scroll sideways →

Drift · Lateral Dynamics
01 · DRIFT · LATERAL DYNAMICS
Brake Module · Test Rig
02 · BRAKE MODULE · TEST RIG
Dunes · Dust Ingress
03 · DUNES · DUST INGRESS
Race Track · Aerial
04 · RACE TRACK · AERIAL
Assembly · Wheel Brake
05 · ASSEMBLY · WHEEL BRAKE
At The Limit · Smoke
06 · AT THE LIMIT · SMOKE
Offroad · Dust
07 · OFFROAD · DUST
Lab · Measurement
08 · LAB · MEASUREMENT
Lap Time · Analysis
09 · LAP TIME · ANALYSIS

PARTNERSHIP

A trusted partner to leading OEMs and Tier 1 suppliers.

Development projects are confidential, so we do not name our clients publicly – we are happy to discuss relevant reference projects in person.

Confidential

Non-disclosure agreements are standard for us – from the very first conversation.

Scalable

From a single specialist to a complete project team – drawn from a large network of permanent and freelance engineers.

Direct

Short decision paths and management you can talk to directly.

Hands-on

Motorsport experience meets series requirements – tested where it counts.

COMPANY

Engineering from Gummersbach, Germany. Since 1996.

ADVANTEC, New Technology GmbH was founded by Wolfgang Wuttke in 1996. Since 2019, Max Wuttke has led the company in its second generation – with the same passion for vehicle engineering and the ambition to bring innovations all the way to series production.

We do not manufacture ourselves. Our team of permanent and freelance engineers supports car manufacturers and suppliers directly in their projects – at their sites in Germany and worldwide.

  1. 1996

    Founding & first patent

    Founded in Gummersbach; patent for monitoring the thermal state of moving bodies.

  2. DEVELOPMENT

    Aluminium SiC brake

    Development of the composite brake disc.

  3. 2019

    Second generation

    Max Wuttke takes over as managing director.

  4. TODAY

    Engineering partner to the automotive industry

    Development, testing and validation with a focus on brakes.

NEWSROOM

Latest from engineering and the company.

All news →
INSIGHT14.11.2026Euro 7: From 29 November, every milligram of brake dust countsFor the first time, an EU standard limits brake wear: 7 mg/km for combustion and hybrid vehicles, 3 mg/km for battery-electric vehicles. What it means for brake development.CAREERS10.11.2026We are hiring: engineers for brakes and test benchesWe are expanding our team of permanent and freelance engineers – for development, validation and vehicle testing.COMPANY28.05.202630 years of ADVANTEC – brake technology from GummersbachFounded on 28 May 1996, now in its second generation: a look back at three decades of brake innovation.

CAREERS

Help shape the vehicle technology of tomorrow.

PERMANENT POSITIONS

Engineers (m/f/d)

Brake technology, chassis, test bench and vehicle testing – working with renowned manufacturers and suppliers, premium company car included, private use too.

Apply now →

FREELANCE

Freelance engineers & specialists

Join our network and work on demanding automotive projects on a project basis.

Join the network →

YOUR BENEFITS

What you can expect at ADVANTEC.

01PERMANENT ROLES

Premium company car

For permanent employees, a company car from a German premium brand is part of the employment contract – private use included.

02

Projects with manufacturers

You work directly inside the development projects of car manufacturers and suppliers – on technology that goes into series production.

03

Worldwide assignments

Testing, validation and research in Germany and abroad – on the test bench, on the track and in the lab.

04

Owner-managed since 1996

Short decision paths, dedicated contacts in Gummersbach and a network of more than 80 engineers and consultants.

CONTACT

Let’s talk about your project.

Briefly describe your challenge – under a non-disclosure agreement (NDA) if required.

ADDRESS

ADVANTEC, New Technology GmbH
Poststraße 2
51643 Gummersbach, Germany